My Cart: 0 item(s)
Jeep 1 Ton Steering Upgrade.
Available for
all makes and models of Jeeps.
Looking to upgrade your stock Jeep steering? Is your lifted Jeep having alignment problems? With our Jeep 1 ton steering upgrade, you eliminate the hard to adjust "Y" stock steering, it allows for a longer drag link to help with your steering angles, and most importantly gives you heavy duty steering that will take a beating and hold up to the off-road abuse.
The rods are a beefy 1.25" diameter DOM, with an almost .25" wall; threads are direct tapped into the tube. This means (unlike a threaded insert) the TRE has full thread engagement into the tube for the length of its threads. On this system the passenger side TRE dust boot is replaced with a polyurethane spacer, which pulls the body of the TRE against this knuckle. This eliminates the tie rod roll that an inverted T setup sometimes has.
While we have had great luck not running a steering stabilizer, if you really have to have one feel free to order this bracket kit from summit racing. This kit will still allow you to easily align our steering setup.
We recommend having this kit installed by a professional 4x4 shop in your area as drilling and reaming needs to be done to knuckles and pitman arm to fit the 1 ton tie rod ends. Installation should take about 2 hours.
|
Resources for drill bits/reamers...
Mcmaster-Carr drill 5/8" bit #2933A28 (direct link)
Speedway Motors - 1 1/2 Inch Per Foot Reamer(direct link)
Looking for answers to common questions about us or our products? See our FAQ here.
19 Questions asked on Jeep Steering Upgrade 1-ton | Under the Knuckle - UTK
•
Ask us anything
Q
charles • 04/16/2020, 2:44:18 PM
will this kit work with a 5.5in lift?
A
04/16/2020, 5:17:11 PM
Yes, but we recommend over the knuckle for that much lift.
Q
matt • 05/15/2020, 4:05:06 PM
Does you utk kit require you to run wheels with backspacing or can i use stock wheels
A
05/19/2020, 2:30:30 PM
15" stock backspace wheels may hit the tie rod ends.
Q
Josh s. • 08/23/2020, 11:01:04 PM
I have a 4.5 lift kit, and it says this will fit up to 4” will it still work with a added drop down pitman arm?
A
09/09/2020, 2:07:14 PM
It will work, but angles start to get pretty steep of your trackbar and drag link. Drop brackets can help.
Q
Scott • 09/09/2020, 0:55:27 AM
Whats minimal lift height needed with the utk setup?
A
09/09/2020, 1:19:05 PM
It will work with stock height vehicles in the UTK setup.
Q
johnathan Velasco • 12/31/2020, 2:37:55 PM
I have a 94 stock steering no lift will it fit with no problem or do I require a lift to make it fit??
A
01/07/2021, 1:01:36 PM
It will fit.
Q
Ken Amen • 02/26/2021, 0:58:00 AM
This says it will fit all Jeeps is that including an '89 Jeep YJ bolt in? Any other modifications required?
A
03/01/2021, 2:42:00 PM
This will not fit a YJ
Q
Moises moraes • 05/30/2021, 2:00:18 PM
I have a 3inch lift will this fit no problem?
A
06/04/2021, 11:31:41 AM
Yes
Q
Fernando • 06/01/2021, 3:00:00 AM
Will this fit on a 1995 Jeep ZJ?
A
06/04/2021, 11:31:41 AM
Yes
Q
Jeffrey Buschard • 06/19/2021, 11:25:46 AM
I have an 01 right hand drive XJ will this work with that some replacement parts I've found that aren't specifically made for RHD does not fit.
A
06/25/2021, 11:08:27 AM
We have not tested with a right hand drive.
Q
Captain black beard • 07/25/2021, 0:11:18 AM
Will stock rims and back spacing work with this kit..?
A
08/12/2021, 2:32:10 PM
Most stock wheels work fine UTK.
Q
Joshua Kinard • 11/10/2021, 12:16:44 PM
would this steering set up fit a 1997 tj with a 3" lift?
A
12/14/2021, 5:35:57 PM
Yes, it would work for that.
Q
Marshall • 01/08/2022, 12:11:49 PM
What brand tie rod ends come with this kit? And what material is the steering links made of?
A
01/12/2022, 10:14:10 AM
The tube is 1.25 DOM with at just under .250 wall. The TRE's are NAPA Proformer Chassis.
Q
Jason • 01/20/2022, 6:31:42 AM
I live in Australia, do you know if this kit is compatible with a RHD 96 xj
A
01/24/2022, 2:08:05 PM
We have not tested with the RHD, not sure about drag link length.
Q
Randall • 02/07/2022, 0:30:28 AM
I have 4.5 inch lift on 33inch tires, 15 inch rims with 3.75 backspace. Will I have clearance issues?
A
02/11/2022, 3:56:46 PM
Should be fine with that backspacing on the wheels.
Q
Andrew • 03/13/2022, 8:33:01 PM
I have a rusty's 8.5" lift on my xj, will this work on mine. I'm assuming I would have to mount on top of the knuckle.
A
04/06/2022, 12:43:58 PM
The over the knuckle kit would be recommended at that lift height.
Q
Morgan Meighen • 03/17/2022, 2:55:39 PM
Will this allow room for a psc hyrdo assist ram on a LJ dana 44 with 4.5 lift.
A
04/06/2022, 12:43:58 PM
Under would be the best bet, but it may require some custom fab to get it all to work together.
Q
Thomas • 05/25/2023, 8:15:54 PM
Is any drilling necessary for install?
A
06/22/2023, 4:47:32 PM
Yes, please see product installation linked on product page.
Q
Thomas Cruz • 11/15/2023, 12:02:20 PM
it says it works with a 4 inch lift or higher. Will this work with a 3.5 inch lift? It's not quite 4... not quite 3.... but in the middle.
A
11/29/2023, 4:44:22 PM
Yes, it would work with a 3.5 inch lift.
Q
William Surrett • 03/27/2024, 7:59:45 PM
Can you still run 15x8 rims on Cherokee XJ
A
04/17/2024, 5:35:16 PM
Factory 15" rims should still work fine with this kit.
Currently Viewing Reviews with a rating of 2. Click here to reset.
9
3
2
1
0
Joe Krempetz
(CA) | April 14th, 2021
I put this kit on my jeep about 3 years back, and since then I've had constant issues with it. Handling is a bit worse than stock, components come without paint etc., and everything wears out quick. When I've reached out to customer service they've given vague answers like "throw a couple poly bushings in, should take care of it." I'm not really getting specific help with my issues, and if other JCR components are needed to make this steering work right, that should be indicated up front or included in the kit.
