My Cart: 0 item(s)
Designed to add storage capacity to JCR rear swing-out bumpers. Add left, right, or both carriers! Coated in a 2 stage satin textured black powdercoat over durable zinc primer finish.
- CNC cut and formed from .188" steel.
- Allows for mounting almost anything (spare tire, jerry cans, tread boards, Rotopax, Hi-lift Jack, fold down table, etc...)
- Optional tire mount not included (see related products below)
- Add them to your bumper at any time.
- Bolt-on installation.
- Proudly designed and made in the USA.
All carrier accessories are à la carte to fully customize your setup. See related products below for tire mount, camera mount, table, jerry can mount, hi-lift mount, etc..
Won't work on JCR bumpers without both left and right side spindle provisions.
Looking for answers to common questions about us or our products? See our FAQ here.
17 Questions asked on Adventure Carrier | Rear Bumper Swing-out
•
Ask us anything
Q
J Ennis • 08/11/2020, 11:16:29 AM
I would like to use this with the Vanguard bumper on a JT to hold a 40 inch tire with wheel that weighs about 135 lbs. It looks like the bumper was tested with a 37 inch tire in the picture. Would the carrier hold up to the weight and size tire I'm wanting to mount?
A
08/12/2020, 3:39:22 PM
That would block the tail light completely. We have only tested this up to a 37" tire.
Q
Cam C • 12/04/2020, 1:06:18 AM
If I needed to have the tail gate down, would this lock in place so it wouldn't swing around? Or would I need to remove the tire swing-out completely?
A
12/04/2020, 12:00:43 PM
There is a locking pin to hold the carrier open.
Q
Jim C • 02/06/2021, 7:50:23 PM
For a 1999 jeep Cherokee limited what bumpers should I be looking at mounting these on?
A
02/08/2021, 10:28:40 AM
https://www.jcroffroad.com/product/XJRV2.html
Q
Lindsey Ross • 03/25/2021, 11:24:18 PM
For the bumper swing out carrier is the spindle assembly (spindle, bearings mounting bolt, and cap) included or must it be ordered separately?
A
04/02/2021, 5:30:54 PM
It's all included.
Q
Erik Omland • 11/08/2021, 2:43:37 PM
What is the height and width of the arm? From the centerline of the spindle to the end of the arm and from the bottom of the mounting plate to the top?
A
12/14/2021, 5:35:57 PM
26.5" from the center of spindle to outside edge wide, ~24" from the base of the spindle (where it contacts the top of the bumper) to the top of the carrier.
Q
Tom • 01/05/2022, 9:25:40 PM
On an XJ without a tire carrier, would the adventure carrier with Jerry cans block the factory license place location?
A
01/12/2022, 10:14:10 AM
Yes.
Q
Jim C. • 02/13/2022, 5:15:36 PM
I intend to buy two of these. Can you provide actionable information on what kind of grease I should use on the bearings? I prefer waterproof, of course. No sense in having it run down the side of my truck or whatever.
A
02/17/2022, 3:24:02 PM
The spindles are sealed on the bottom with a dual lip seal and up top with an o-ring, so no danger of any grease running out. You can use whatever bearing grease you have. We like Lucas marine grease or Red "N" Tacky.
Q
Jim C. • 02/18/2022, 8:25:35 AM
Any problems with using (link removed: Electrical Marine Lithium Grease)
I like this product because I've got antennas that may be mounted on the swing-outs and HF radios prefer hinged items all be well grounded. I've already had to strap all the doors and even the muffler and gas tank cover to reduce HF noise.
A
03/04/2022, 1:55:11 PM
No problems, not much grease stress on these bearings at all.
Q
Joe • 04/14/2022, 4:16:52 PM
What happens to the rear Bronco camera with the offset of the adventure carrier for spare?
A
04/15/2022, 10:45:47 AM
It can be relocated to the spare using our Camera Relocation Bracket
Q
Chase Fann • 05/31/2022, 9:36:59 AM
What is the weight load each Adventure Carrier can hold? Looking to add a spare tire platform on the tire for some extra storage, but want to see the weight limits are.
Thanks! Love all the products purchased from JCR so far!!!
A
06/09/2022, 2:54:02 PM
We don't have official weight ratings on them as it also depends on what bumper they are going in, but around 150 pounds seems like the max without things starting to flex a ton.
Q
David • 01/30/2023, 0:20:46 AM
Where can I purchase the latch only?
A
01/30/2023, 4:19:30 PM
Give us a call: 269-353-1184
Q
Derek • 03/04/2023, 7:15:02 PM
Can you mount the spare tire on the drivers side so it doesn't block visibility? 97 Jeep XJ
A
03/13/2023, 4:14:43 PM
Yes the spare can go on either carrier.
Q
Rich Foley • 04/25/2023, 4:28:11 PM
Will these work with the older JCR bumper that had the tire mount that went all the way across?
A
05/01/2023, 12:03:22 PM
It does not.
Q
Matt • 05/22/2023, 2:14:56 PM
On a 2016 JK with the passenger side mounted carrier and 37, would the tail gate open with the tire? Or would I have to open the tire carrier and then open the tail gate?
A
05/22/2023, 3:56:24 PM
You would need to open the swing-out first before you'd be able to open the tailgate.
Q
Matthew • 04/13/2024, 3:39:11 PM
If you have 2 installed (one tire and one can carrier, or 2 can carriers), are there any issues with clearance between them?
A
04/15/2024, 2:56:26 PM
No, you can install two carriers with either of those combinations without issue.
Q
Patrick • 04/26/2024, 11:38:09 AM
Is the latch provisioned/designed to be able to take pad lock for added security and prevent somebody from opening the carrier?
A
05/20/2024, 3:06:04 PM
Not a pad lock, but a locking bail pin can be used to mechanically lock the latch from opening.
Q
Clay • 07/16/2024, 4:59:16 PM
Is there enough material on the far side of the swing out to weld a 2 inch receiver for a hitch mounted bike carrier?
A
07/17/2024, 10:20:15 AM
There is a lip on the edge of the swing out that may allow you to do something like that, but not enough material to handle that weight of a bike(s) without adding some reinforcements.
1
0
0
0
0
Nicholas Joiner
(Flagstaff, AZ) | June 30th, 2021
I purchased both left and right swings. They are awesome. They look great and are the only dual swing bumpers for the XJ that I could find. I think the price is a little steep, there are a few design improvements needed, and I had to get a replacement spindle, but overall great!
